The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
Are you currently looking for critical info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bathtub isn't exactly rocket science, yet it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately challenging task. If the old bathtub is readily accessible, the job can relocate rapidly; if you have to open up a wall to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the job is within a house handyman's skills, although you will certainly need a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have certified yourself for the job and also are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to think about employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly help you set up a brand-new tub in your restroom if you have currently purchased a brand-new tub and do not require to change the plan of your previous water supply pipelines.
Your devices and material checklist need to consist of the following:
Planning for the Installment
First of all, the sustaining framework provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bath tub till the level reviews degree.
To set up faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipeline by making a compression join; after that do the exact same for the other tap.
Switch on the supply of water as well as check all joints and brand-new pipework for leaks and also tighten them if necessary. Fill the bathtub as well as also inspect the overflow electrical outlet and the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait up until the bath tub has been made use of at least once as this will resolve it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type needs to be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a rigid seal, causing the water to pass through the wall in between the bathroom and the tiling, leading to complications with dampness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked paper or soft rope. Remember to always load the bath tub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads on Installing A Bathtub, I thought sharing that excerpt was smart. Those who liked our blog entry plz make sure you remember to pass it around. Thanks a bunch for your time. Come back soon.
Make An Appointment Report this page